General device configuration

Device Configuration

PRTK Code

Name

Part Number P/N

Serial Number S/N

System Admin Data

Contact

Location

Battery replacement notification

DEBUG

factory_part_number / nominal-json

override_part_number / config-cgi

getUnifiedPartNumber() / JS

serial_number / nominal-json

factory_serial_number / nominal-json

override_serial / config-cgi

getUnifiedSerialNumber() / JS

Command configuration

Command

Disable remote shutdown

Disable remote commands

Data Log configuration

Data Log

Enable Data Log

Backup UPS data log at boot

General Network configuration

Generic Network Configuration

Hostname

Network protocol

Static IP DHCP

IPv4 Configuration

IP Address

Netmask

Gateway

Primary DNS

Secondary DNS

IPv6 Configuration

Enable IPv6

Disabled Enabled

Privacy Extension

Prefix Delegation

Accept Router Advertisement

Link-local address

-/-

Global Unique address

-/-

Gateway

DNS

Global Unique address / Prefix Length

Gateway

DNS

FTP

Enable FTP protocol

Serial network tunneling

Enable Serial tunneling

UDP

Enable UDP

UDP port

UDP password

Password

Retype Password

Firewall configuration

Firewall

Enable Firewall Rules

INCOMING Rules

Default incoming rule:

You must test the rules before confirm...

Test temporarily the rules with immediate effect.

In case of problems due wrong rules, you can restart the Netman and last previous confirmed rules are recalled, so you can adjust rules again.

Confirm rules

In case of correctness, you can confirm the tested rules and make them permanent and active from the next reboot.

Wake On Lan

Wake on lan

Enable Wake On Lan

Mac addresses & Delay

MAC Address 1

Delay next (sec)

MAC Address 2

Delay next (sec)

MAC Address 3

Delay next (sec)

MAC Address 4

Delay next (sec)

MAC Address 5

Delay next (sec)

MAC Address 6

Delay next (sec)

MAC Address 7

Delay next (sec)

MAC Address 8

MODBUS/BACNET configuration

MODBUS

Enable MODBUS

BACNET

Enable BACNET

BACNET Data

BACNET Address (Number)

BACNET Client (IP)

RIELLO CONNECT

To enable Riello Connect Service please insert the P/N and the serial number S/N in the General Configuration page.

PAIRING

Status

Registration token

Copy the Registration token in the Riello Connect user account page -> Appliance -> Add UPS

or press

If doesn't work, copy and paste the following URL in your browser:

___REGISTRATION_FULL_LINK___

Date & Time configuration

Current date is -

Set a new date

Date

Hour

Minutes

NTP & Timezone configuration

Current date is -

Set a new timezone

Select the right timezone

Set a NTP Server

NTP server address (IP)

Email configuration

Enable Email

Mail Host & SMTP

Mail host

SMTP port

Other parameters

Sender address

Transport

Username

Password

Emails

	Email #1	Email #2	Email #3
Device Lock
Overload / overtemp
General Failure
On Bypass
Input blackout
Battery low
Communication lost

Email Report

Send report every day at 00:10

Send report every Sunday at 00:10

SYSLOG

Enable remote SYSLOG

Server configuration

SYSLOG server IP

Server UDP port

UPS Lock
Overload / overtemp
UPS Failure
On Bypass
Battery work
Battery low
Communication lost
Mainteinance
Switch open
Anomaly
Command active
Warning

General device configuration

Device Configuration

System Admin Data

DEBUG

Command configuration

Command

Data Log configuration

Data Log

General Network configuration

Generic Network Configuration

IPv4 Configuration

IPv6 Configuration

FTP

Serial network tunneling

UDP

UDP password

Firewall configuration

Firewall

INCOMING Rules

You must test the rules before confirm...

Test temporarily the rules with immediate effect.

In case of problems due wrong rules, you can restart the Netman and last previous confirmed rules are recalled, so you can adjust rules again.

Confirm rules

In case of correctness, you can confirm the tested rules and make them permanent and active from the next reboot.

Please a wait few seconds for testing yourself the rules, before confim and save...

Wake On Lan

Wake on lan

Mac addresses & Delay

SNMP configuration

SNMP

CONFIGURATION MODE

SNMP configuration file upload

Current configuration file

SNMP configuration wizard

Snmp version

SNMP v1/v2

COMMUNITY

SNMP v3

USERS

TRAP RECEIVER

Test SNMP Trap (please click save before testing)

MODBUS/BACNET configuration

MODBUS

BACNET

BACNET Data

RIELLO CONNECT

PAIRING

Date & Time configuration

Set a new date

NTP & Timezone configuration

Set a new timezone

Set a NTP Server

Email configuration

Mail Host & SMTP

Other parameters

Emails

Email Report

Test email (please click save before testing)

JSON

JSON

Receiver

Send notification on event

SYSLOG

SYSLOG

Server configuration

Test syslog connection (please click save before testing)